ICX Global Universal Remote ENT 6412 User Manual

4
KNOW YOUR REMOTE  
Congratulations!  
1
The diagram below provides a brief description of each key on your universal remote control.  
ICX Global provides these function descriptions as a general guide to allow you to become more  
familiar with your remote. Functions may vary between different services. Please refer to your  
set-top box manual for descriptions of specific functions.  
This 4 mode remote control has been pro-  
grammed to control your Motorola set-top  
box and can be programmed to control up  
to three additional entertainment  
components by following these easy  
instructions.  
User’s Guide for the  
ENT 6412  
4-in-1 Cable TV Remote Control  
for Motorola®  
Digital set-Top Boxes  
Use this guide in conjunction with your  
set-top box manual  
The volume and channel controls are set  
to control the cable converter. This can be  
modified by following the instructions in  
sections 7 and 9. This remote has a  
master power feature for powering all  
components together. See details in  
section 8.  
VISIT US ON THE WEB  
You can find programming instructions  
and codes for all of our remote  
controls, as well as information about  
our other products on our website:  
w w w . i c x g l o b a l . c o m  
BEFORE YOU BEGIN  
2
Please plug your television power cord  
into a separate wall outlet instead of the  
power outlet on the cable box.  
Tune your television to channel 2, 3 or 4  
as directed by your cable provider.  
3
INSTALL BATTERIES  
Two AA batteries must be installed before  
you can program or operate the remote  
control.  
1. Remove the battery compartment cover  
located on the back of the remote control.  
2. Place the batteries in the compartment  
in positions matching the picture below.  
3. Replace the battery compartment  
cover.  
IMPORTANT  
NOTE  
!
The Enterprise remote control is already programmed with the code for your Motorola® Cable  
Converter. The following sections will help you program your remote to control your other  
entertainment components.  
© 2004 ICX Global, Inc.  
All rights reserved  
Part Number ICX18346, version 1.0  
07012004  
Use only new AA Alkaline batteries  
to insure consistent operation  
Test the code by trying various functions. If the primary function keys fail to respond  
satisfactorily try the next code listed for the manufacturer.  
3
5
SMARTSCAN™ AUTOMATIC PROGRAMMING  
The SmartScanprogramming instructions can also be found on the battery cover of the remote  
control. SmartScanwill allow you to easily try all the available programming codes for the  
selected device and find the best match. If you prefer manual programming or already have the  
device codes you may also program the remote manually using the steps in section 6.  
If you have tried all the codes listed for the manufacturer and the device does not  
respond, try to program the device using SmartScanas described in section 5.  
Remember to record your device codes in section 11 when you are done.  
7
PROGRAMMING VOLUME CONTROL  
Turn on power for the device to be programmed.  
1
Begin the SmartScanprocedure by pressing and holding the associated device key  
(AUX, VCR, CBL, TV) until all device keys on the remote begin to flash (approximately 3  
seconds). Release the power key.  
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR  
and DVD through the Television. To allow volume control through a different device:  
2
Press and hold the CBL device key until all the device keys begin to flash. Release the  
CBL key. The CBL key will continue to flash.  
1
3
4
If the device you’re are attempting to program matches the selected device key (e.g. TV  
component with the TV device key) proceed to step 5.  
Press and release the VOLUME UP key, the CBL key will remain on.  
2
If the device you’re are attempting to program does not match the selected key (e.g. a  
second VCR programmed to the AUX device ), locate the correct prefix code for the  
device you wish to program from the table listed below. Press and release the number  
key that matches the prefix code.  
Press and release the VOLUME DOWN key. The CBL key will turn off when VOLUME  
DOWN is pressed, and will turn on when released.  
3
Press and release the key corresponding to the device you wish to use to control  
volume. (TV or AUD) After you release the key, the CBL key will flash three times and  
turn off.  
4
Prefix  
Device  
0
1
4
5
TV  
VCR/DVD/PVR  
Audio Receivers  
Combo Units  
To return volume control to the default state:  
Press and hold the CBL device key until all the device keys begin to flash. Release the  
CBL key. The CBL key will continue to flash.  
1
5
6
7
Press and release the POWER key. The device key will stop flashing and remain on.  
Point the remote control at the selected device.  
2
Press and release the VOLUME UP key. The CBL device key will stop flashing and stay  
on. Press and release the VOLUME DOWN key, and then press and release the OK key.  
After you release the OK key, the CBL device key will flash three times and turn off.  
Press and hold the UP ARROW key until the device turns off. While holding the UP  
ARROW key the remote will send a new code approximately once every second. The  
device button will blink each time a new code is sent. If you pass the code that turns off  
the device, press the DOWN ARROW key to return to the previous code.  
Master Power Control  
8
The Master Power function allows you to turn off and on two or more devices simultaneously  
with a single press of the power button. The following steps describe how to program the  
Master Power Control function:  
When the device turns off, you have found a candidate code. Press the POWER Key to  
turm device back on. Test various functions using the remote control to determine if this  
code will work. If primary functions do not work, make sure the device is still on then  
resume SmartScanby pressing the UP ARROW key to find another device code.  
8
9
Press and hold the CBL device key until all the device keys begin to flash. Release the  
CBL key. The CBL key will continue to flash.  
1
Press and release the POWER key.  
2
Once you have found a satisfactory code, press OK to lock the code. The power of the  
device must be on. The device key will then flash three times. Go to section 10 to recall  
and record your device codes. When all the codes have been attempted the device  
button will flash rapidly.  
Individually press and release each device key corresponding to the components you  
wish to be controlled by Master Power (starting with the cable device key). NOTE: If no  
keys are pressed in this step, no change will occur in Master Power programming.  
3
Press and release the POWER key. The CBL key will flash three times and turn off.  
4
5
Manual Programming  
6
Manually turn on all devices. Then test the Master Power control by pressing the  
POWER key.  
To manually set up the Enterprise to operate a device, find the manufacturer of the device in  
the list of manufacturers’ codes. The codes are logically grouped by device type in section 12.  
Then perform the following steps:  
To disable Master Power, repeat the previous steps selecting only one device for Master Power  
(any device can be selected). The remote will now control the power ON/OFF of each device  
separately.  
Press and hold the device key to be programmed until all device keys begin to flash  
(approximately 3 seconds). Release the key. The selected device key will continue to  
flash.  
1
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER  
key in normal operation will cause the remote to transmit the POWER on/off commands for  
those devices selected during Master Power programming,  
Enter the four digit code for the desired device using the number keys. After pressing  
the first digit, the device key should light and remain on. If the programming is  
successful. After the last digit is pressed the device key should flash three times and  
turn off.  
2
To override this and transmit a POWER on/off command for a device not included in the Master  
Power selection, press the DEVICE key for that device and immediately press the POWER key.  
 

GTI Indoor Furnishings Graphiclite 100 User Manual
Haier Flat Panel Television LE50H3280 User Manual
HannsG Computer Monitor HB171AB User Manual
Harbor Freight Tools Automobile Accessories 96658 User Manual
Hotpoint Washer 9577 User Manual
HP Hewlett Packard Laptop VS832UT User Manual
HP Hewlett Packard Laptop X1000 User Manual
HP Hewlett Packard Window 315379 008 User Manual
IBM Network Card 3270 User Manual
iLive DVD Player ID200B User Manual